facebook instagram Whatsapp
Certified Master Roofers in Metro Vancouver

No worries. Let's try it this way

Please fill your details, and we will provide you with an estimate in a very timely manner.

Surrey, BC · Residential Roofing

Skylight Installation & Replacement in Surrey, BC

A house roof with two skylights set into dark asphalt shingles

From inside a room, a skylight looks like a window in the ceiling. In a typical house with an attic, it is three stacked layers: the ceiling opening, a shaft that crosses the attic, and the unit set into the roof. Where the ceiling follows the roof slope, there may be little or no shaft. Each layer has its own job and often its own trade. GoodVans Roofing takes on skylight installation and replacement for Surrey homeowners, and planning from the ceiling up shows what each project involves.

Three layers, from the ceiling to the roof

The room. The ceiling opening and its finish decide how the light spreads and how the opening looks. This layer is interior work: drywall, trim and paint. It sits outside roofing unless the scope says otherwise.

The shaft. Where an attic separates ceiling and roof, a framed and lined passage carries light through it, and in a cold, ventilated attic its walls act like an exterior wall of the house and need insulation and an air barrier. A shaft that lacks either can let warm, moist room air reach cold surfaces, and some damp complaints at skylights start here rather than at the roof.

The roof. The unit itself, with its glazing, frame and seals, plus the flashing and roofing that shed water around it. Some units are deck-mounted, fixed directly to the roof deck. Others sit on a curb, a raised frame built up from the deck, which manufacturers present as the usual choice on low-pitch roofs. Each manufacturer sets the pitch range and the flashing system for its units by roofing type, so the product, the roof's pitch and covering, and the installation instructions decide which suits.

A problem in one layer does not prove the others are sound, so each is worth checking before any part is agreed.

A roofer in a hard hat checking the flashing around a skylight

A new skylight, from ceiling to roof

A new skylight starts with the room, but the roof decides where it can go. GoodVans Roofing weighs the pitch and layout of the roof, the room that needs light, and units that suit the space and budget. Some positions will not work, and some need a different unit or location.

The middle layer is the easiest to overlook. Depending on how the house is built, a new opening may mean framing, insulating and sealing a shaft through the attic and finishing the ceiling, or a much shorter opening under a vaulted ceiling. Cutting or reframing rafters, trusses or joists is a structural modification that needs assessment by an appropriate professional before work begins, and the scope should name who carries out each part, because shaft and ceiling work may involve trades other than the roofer.

A new skylight with dark metal flashing in an asphalt shingle roof

Replacing a skylight that is already there

Replacement starts at the top. The existing unit is removed and its successor is set into the same opening, provided the new product fits it, and tied in with the flashing and roofing around it. Existing flashing is reused only where it is suitable, sound, compatible with the new unit and allowed by that unit's manufacturer instructions; looking intact and fitting the opening are not enough. If the original model is no longer made, a current product of similar size and mounting may suit; if not, the opening, curb or flashing may need adjusting, which moves the job closer to a new installation.

The other two layers may be able to stay as they are. Whether they should depends on what the replacement is meant to fix. A cracked pane or a failed seal is a unit problem. Recurring damp on the shaft walls may not be, and a new unit fitted above a poorly insulated shaft can leave that problem in place.

Two roofers lifting out an old skylight with a weathered frame

Moisture at a skylight, layer by layer

Water near a skylight can have several sources. Rain may be getting past the unit, its flashing or the roofing beside it. Condensation can form on the glazing or on shaft walls when warm, humid indoor air meets a cold surface, which is not necessarily a sign that anything is defective. Ceiling staining can also come from water entering elsewhere and travelling. Timing helps: wetness during rain points one way, dampness on cold, dry mornings another. Replacing the unit alone may not resolve condensation linked to shaft insulation, air leakage or indoor humidity, and new glazing is no guarantee against leaks in the roofing around it. Where the source lies outside the skylight altogether, finding it is a matter for roof repair and maintenance in Surrey.

A man on a scaffold checking a stained skylight shaft with a moisture meter

When the roof is being replaced as well

Depending on how the roof is built and what the replacement includes, a re-roof can expose the flashing around each skylight, which can make it a sensible point to decide each unit's future. A unit in good condition and compatible with the new roofing may stay, with new flashing integrated into the new covering. One that is ageing, mismatched to the new system or already giving trouble may be worth replacing while the area is open. Make that call during planning for roof installation and replacement in Surrey, not after tear-off has begun, and decide at the same time whether the shaft needs anything.

Writing the scope layer by layer

For each layer, say what is included. At the roof: new or existing opening, deck-mounted or curb-mounted unit, fixed or opening, which flashing is new and which stays, and the condition of the roofing around it. In the shaft: whether framing, insulation or lining changes, and who does it. In the room: whether ceiling finishing is included. Add how conditions found once the opening is exposed will be handled.

Skylight installation questions from Surrey homeowners

Can the light shaft stay as it is when the skylight is replaced?

It can, provided the new unit suits the existing opening and the shaft is in good condition. If the replacement unit has a different size or mounting, or the shaft shows staining, gaps in insulation or air leaks, it may need work at the same time.

The walls of our light shaft get damp and stained. Is that the roof?

Not necessarily. Rain getting past the unit or flashing can cause it, but so can condensation on shaft walls that are under-insulated or leak warm air. When it appears, and whether it follows rain, helps narrow the cause before deciding on roof work, shaft work or both.

Can a skylight go on a low-pitched part of the roof?

Sometimes. Manufacturers typically specify a slope range for each product, and lower slopes often call for a curb-mounted unit with flashing designed for that pitch. Some low-slope or flat areas may need a different product or location altogether.

Does a new skylight need a permit in Surrey?

It depends on the work. The City of Surrey's renovation permit guidance notes that changes to structural elements may require signed and sealed drawings from a registered professional. Confirm requirements with the City before work is booked rather than assuming either way.

Starting with the right layer

If you are planning a skylight, or one you have is causing trouble, start by working out which layer is involved. Ask GoodVans Roofing to assess it, or see how the skylight installation and replacement service works.

Let's talk

Contact Info

  • Address GoodVans Roofing 207 W Hastings St, Unit 1210, Vancouver, BC V6B 1H7, Canada
  • Contact Number 17783778209
  • Email ID info@gvroofs.ca
facebook instagram Whatsapp