facebook instagram Whatsapp
Certified Master Roofers in Metro Vancouver

No worries. Let's try it this way

Please fill your details, and we will provide you with an estimate in a very timely manner.

Vancouver, BC · Residential Roofing

Flashing Install & Repair in Vancouver, BC

A roofer fitting step flashing where a brick chimney meets an asphalt shingle roof

Most of a roof is straightforward: water lands on it, runs down it, leaves at the bottom. The parts that are not are the ones where that run gets interrupted — a wall rising out of the slope, a chimney coming through it, two planes folding together, a vent poking out. At each of those the covering has to stop and hand over. Flashing is what it hands over to. GoodVans Roofing carries out flashing repair and installation on houses across Metro Vancouver.

What flashing is doing

Think of it less as a product and more as an arrangement. Shaped metal is involved, usually several pieces, but what makes the arrangement work is how they sit — which laps over which, by how much, and facing which way. Nothing about it depends on being airtight. Water arrives, meets the overlap, and gets sent on.

The practical consequence is that a detail can stop working while the metal still looks serviceable. A piece that has lifted along one edge, slipped out of its lap, corroded through at a fold, or went in misaligned is no longer steering water where it was meant to. Deterioration, displacement and poor detailing all get there, and from the ground they look much the same.

A roofer pressing metal flashing into place where a shingle roof meets a sided wall

Where the roof has to change

A few kinds of place account for most of it: a wall standing up out of the slope, a chimney passing through, a valley where two slopes fold into each other, and the small penetrations that vents and pipes make. A skylight belongs on the list too — from the roof's point of view it is an opening with a detail worked around it. Chimneys, skylights, valleys, vents and edges all sit within what GoodVans Roofing handles.

Chimneys earn a note of their own. Once one is out of service it stops registering as part of the roof — but the masonry still stands in the covering, and the detail at its base is still the only thing moving water past it.

Metal valley flashing running between two planes of an asphalt shingle roof

Three situations, and they lead different places

Three answers cover most of it.

Nothing wrong with the roof; the detail has come apart. Corrosion, a slipped lap, movement, or an integration that was wrong from the start. Where the covering around it is still doing its job, this is repair territory, and GoodVans Roofing carries that work out. How localised it stays depends on the detail — some are reachable on their own, others need adjacent covering lifted and reinstated.

Nothing wrong with the detail; the roof around it has gone. Flashing works only in company with the covering it laps into, so where that covering has failed, new metal buys very little. The junction showed the water. The roofing is what needs doing.

The roof is coming off regardless. Every junction a re-roof reaches becomes part of that job, and each one is kept, renewed or re-integrated on its own merits — nothing about being a chimney or a valley settles it in advance.

Which applies is not answerable from inside the house. A mark on a ceiling gets someone onto a ladder; what sets the scope is what the ladder finds.

Step flashing along the junction of a shingle roof and a sided wall

Sealing a detail is not the same as detailing it

A bead of sealant over a gap is commonly offered for a leak at a chimney or a wall, and it is worth understanding what it reaches.

It reaches the gap. What it does not reach is the reason the gap is there. Where a piece has slipped or was lapped the wrong way round, the arrangement underneath is still wrong and the sealant has become the only thing holding water out — a job it was never shaped to do. Where a quote for a junction leak is mostly sealant, the question worth asking is what happens to the metal.

None of which is an argument against it. Sealant belongs in plenty of properly detailed repairs. It cannot stand in for one.

What flashing repair and installation involves

A look along the roofline
The affected area cleared
Metal cut to the roof
New flashing goes in

New work and repair work start from different places. New work begins with a clean surface and metal cut to the roof in front of it — cut to fit rather than cut to size, which is the difference between a detail that functions and one merely present. Repair work begins with a look along the roofline to establish what is involved; then the affected area is cleared and new flashing goes in. Where a detail is past being worth repairing, replacing it outright is available.

Rust, gaps, movement. That is what an assessment comes down to, and between them they say whether an arrangement is still holding its shape.

A roofer fastening a flashed pipe vent boot into a shingle roof with a drill

Settling what the job covers

Four things are worth on paper before anyone starts: which junction is in scope, whether the metal or the roofing it sits in is the subject, how far back the covering must come, and what is being kept.

Roof-to-wall junctions add a fifth. Flashing there ties into whatever the wall is finished in, not just into the roof. Work on a wall finish — new siding, new stucco — can disturb or alter that integration, so where a house has been re-clad since the roofing went on, the junction is worth checking.

Where roof replacement is in the picture, each detail's fate belongs in that scope. And since some junctions only show their condition once the covering is off, settling that beforehand is fair.

  • Which junction is in scope
  • The metal or the roofing it sits in
  • How far back the covering must come
  • What is being kept
  • Where a junction ties into the wall finish

Common questions

Our chimney has not been used in years. Does its flashing still matter?

Yes. It is still masonry standing in the roof, and the junction at its base still has to move water past. If anything a disused chimney gets less attention, since nobody is thinking about it.

We had the siding redone. Could that be where the leak started?

Worth checking. Flashing at a roof-to-wall junction ties into the wall finish, so work on that finish can disturb or alter the integration. It may be perfectly intact — but something did change at that junction shortly before the leak appeared, which makes it a sensible place to look.

Why would a flashing detail leak in some rain and not others?

Because it works by shape rather than by seal. A detail slightly out of position can cope with water running straight down it and fail when rain is driven sideways into the junction, or arrives faster than the overlap carries away. Not proof of flashing, but it fits how flashing fails.

How much roofing has to come up to reach the flashing?

That follows from the junction and how the detail was integrated. Flashing laps into the covering, so reaching it means lifting some back — not much at a vent, more at a wall or a valley. Worth having as a figure beforehand.

Where to start

Water showing up at a junction tells you where, not what. Whether the metal, the roofing it laps into, or both are in play is the first thing to establish. Get in touch to have the junction looked at, or read what the flashing installation and repair service covers. If the question turns out to be broader than one detail, repair and maintenance is the right ground.

Let's talk

Contact Info

  • Address GoodVans Roofing 207 W Hastings St, Unit 1210, Vancouver, BC V6B 1H7, Canada
  • Contact Number 17783778209
  • Email ID info@gvroofs.ca
facebook instagram Whatsapp