facebook instagram Whatsapp
Certified Master Roofers in Metro Vancouver

No worries. Let's try it this way

Please fill your details, and we will provide you with an estimate in a very timely manner.

Vancouver, BC · Commercial Roofing

Torch-On Roofing in Vancouver, BC

A finished torch-on membrane roof with a roof drain and parapet, evergreens and mountains beyond

A torch-on roof arrives as rolls and stops being rolls. Heat bonds each sheet down and bonds adjoining sheets to one another, so by the end there is one surface rather than a collection. Almost everything worth knowing about such a roof — how it holds up, what can be put right alone, what a problem costs — traces back to that. Installing, repairing and maintaining torch on roofing is work GoodVans Roofing does for commercial and industrial property around Metro Vancouver.

What it is

Modified bitumen is a family. Torch-on is one way of getting it onto a building: each sheet's underside is heated with a propane torch as it goes down, so the bitumen softens and bonds straight onto the surface prepared for it.

That is the whole of the distinction — the application, not the material. Other low-slope systems attach by other means, and the choice shows up long afterwards, in how the roof behaves and what working on it involves. For the comparison across systems rather than this one, low-slope roof systems is the wider view.

A roofer heat-applying a roll of modified bitumen membrane with a torch on a flat roof

How separate sheets become one roof

A bond can only be as good as the surface under it, which puts preparation higher up the list than its place in the schedule. Cleaning and priming are how GoodVans Roofing gets a surface ready, and what each involves follows from the surface — priming gives heated bitumen something to hold.

Then the laps, where one sheet overlaps the next. Getting them right is a substantial share of the installation, not a finishing touch. Sections are heated and bonded in turn, seam checking and leak testing at close-out as the project requires.

Which leaves an awkwardness for anyone inspecting a finished torch-on roof. The two things that decided how it performs were both completed and covered over before there was a roof to look at.

A roofer rolling the lap where two torch-on membrane sheets overlap

Where the membrane stops being the whole question

The field is the easy part. Anything coming through the roof — pipework, a vent, a curb, equipment standing on it — breaks the membrane, and every break has to be closed off and worked back into one surface.

Those places do not age at the field's rate. More transitions, more detailing, and the consequence is divergence: an open area still doing its job can sit feet from a termination that is not.

Drainage comes into it too, for the roof's reasons rather than the system's. Water that keeps standing asks more of the membrane, the laps and the detailing beneath.

Torch-on membrane carried up and over a parapet wall with metal cap flashing on top

Looking at an existing torch-on roof

Most people meet a torch-on roof years after it went on, with the building or the lease. The preparation and the lap work are covered over, so neither reads off the surface.

Covered over is not unknowable. Specifications, warranty paperwork or a contractor's file may record what was done. Condition is evidence in its own right — how laps and terminations behave says something about how they were formed. And opening a small area answers directly.

What an assessment establishes is the present tense, which is what a decision turns on. Trouble in one place or several with nothing linking them? The laps and terminations, or the field? Is the surrounding membrane serviceable? Is drainage contributing? And what is up there and underneath, since that governs what new work means.

Between them they tell a contained repair from a larger conversation.

  • Trouble in one place or several
  • The laps and terminations, or the field
  • Is the surrounding membrane serviceable
  • Is drainage contributing
  • What is up there and underneath

Repairing an area, or replacing more

All three are on the table at GoodVans Roofing — install, repair, maintain — so none is a default in disguise.

A contained repair fits where the fault has edges, an identified cause, and sound membrane and detailing around it. One lap opened in one spot is not the same finding as that condition in four.

The scope widens for reasons, and the reasons are findable: the same trouble in areas with nothing linking them, drainage that cannot be fixed without going into the assembly, or something beneath the membrane. Neither a share of the surface nor a number of years decides it.

When another route may suit better

Between a repair and a replacement sit two other routes.

Coatings go over an existing commercial or industrial system instead of replacing it, and GoodVans Roofing applies them — though not to whatever happens to be there. Whether one suits depends on the assembly beneath and on coating compatibility, which assessment settles. Roof coatings and waterproofing sets out the route.

Where the useful thing is watching how a roof changes, roof asset management plans covers it.

What torch on roofing work involves

Assess the existing roof
Prepare and prime
Heat and bond the membrane in sections
Check seams and test for leaks
Clear the site and walk the result

The shape GoodVans Roofing works to: assess the existing roof and whether torch-on suits it, prepare and prime, heat and bond the membrane in sections, check seams and test for leaks, then clear the site and walk the result with the client. Each step runs as the roof requires.

Step one matters more than its position suggests. Whether torch-on belongs on this building is a question; finding it already up there is not the answer.

One more thing belongs in planning, not specification. Because the membrane is heat-applied, the job reaches past it: what sits under the deck, what stands beside the building, and how the place keeps running all belong in the scope — a first-week conversation on a constrained or occupied site.

A completed torch-on roof with a drain, vent and parapet, the downtown skyline behind

Common questions

We bought the building with the roof on it. What can be known about how it was installed?

More than you might assume, and from three places: records that came with the building, condition itself, and a small opened area where warranted. Specifications or a contractor's file may describe what was done; how laps and terminations behave reflects how they were formed. None is complete, which is why current condition is what a decision rests on.

A seam has opened in one place. Does that tell us anything about the other seams?

Not on its own — one opened lap can be local, with a local cause. What gives it wider meaning is company — the same condition elsewhere points where a single instance does not. Establish that first.

The building stays open while work happens. Does that affect a torch-on job?

The planning rather than the system. Heat-applied work means what is under the deck and around the building forms part of the scope, with access, staging and occupant impact. Settle it at quote stage.

Someone has told us the whole roof needs replacing. How do we test that?

Ask what it rests on. It should point at something specific — trouble in areas with nothing linking them, drainage that cannot be fixed in place, or something beneath the membrane. Neither age nor a share of the surface is a reason by itself. If the answer is a number, ask for the finding.

Where to start

Trouble on a torch-on roof could be the field, the laps, the terminations or the drainage, and which it is decides the size of the answer. Settle it first. Get in touch for an assessment, and the torch-on roofing service page covers the work itself.

Let's talk

Contact Info

  • Address GoodVans Roofing 207 W Hastings St, Unit 1210, Vancouver, BC V6B 1H7, Canada
  • Contact Number 17783778209
  • Email ID info@gvroofs.ca
facebook instagram Whatsapp